You may have to register It's not uncommon on cheap guitars or guitars that had the strings too tight, or stored for a long time, to develop a warp somewhere around the 10th fret. these guitars are 'through neck' The old fingerboard came off quite easily, however a substantial bow to the neck remains. First off, you need to check which way your neck is warping. What should I do with a bass with a warped neck? The neck simply would not straighten out, no matter what we did with the truss rod – even with the truss rod completely loose, the neck had a severe back bow. This week we took in a 1960’s Fender P-Bass for a refret that had a severely warped neck. This neck straightened out nicely, and is now ready for the next step: installing the frets. In this instance, we’ve decided to do a heat press. The neck has a dip around the 5th fret of the E string and a dip around the 7th fret of the G string. It's really hard to tell from a photo, but it doesn't seem to be warped to me. before you can post: click the register link above to proceed. if you neck is warped can you see it with the naked eye, how can you ensure your guitar neck is perfactally straight? Now look down the bass side of the fingerboard (See PHOTO 3). link above. The neck is then slowly heated, slipping the glue joint, and then we wait several hours as the neck cools ans the glue dries. This … A good light source for this visual check would be a well-lit window. Our Setup Workshop will equip you with Lie the guitar flat on its back on the table, the headstock pointing towards you. Give us a ring…we would prefer to talk the specifics of that with you over the phone: 415-865-5424. I've got 60 guitars...but 49 trumpets is just...INSANITY! Other than an eye balled check if its twisted or warped is there any other way to tell if your neck is in perfect condition ? select the forum that you want to visit from the selection below. You have to ignore the nut and focus on the frets when you look down the neck from the nut. : Sometimes we can true the fingerboard with sanding and radius beams, but this bass has such a thin rosewood fingerboard that it just wouldn’t work – we’d blow right through it. All times are GMT-8. We provide high-quality guitar repair, and teach guitar maintenance and building workshops to all levels of musicians. As it is tightened, it exerts more pressure on the neck forcing it to bend backward in the opposite direction of the string tension. Thanks again. WTF! Repeat the process with the treble side of the fingerboard. It's not uncommon on cheap guitars or guitars that had the strings too tight, or stored for a long time, to develop a warp somewhere around the 10th fret. LEARN TO DO WHAT WE DO- If it is bowing inwards (dipping), then your neck has too little stress on it. We first place the neck in our heating caul, like so: The neck is placed against a flat aluminum bar, which is heated with a heating blanket, which in turn is sandwiched by another aluminum bar, and then the whole thing is clamped tight with the rounded clamps you see in the above picture. The nut is supposed to be higher for the lower strings. If this is your first visit, be sure to (You can unsubscribe anytime). The truss rod is a metal rod inside the neck of your bass. Also, hold the bass / neck so that the surface of the butt of the neck is in the same "plane" (at the same elevation) as the headstock end of the neck. When I "eyeball" relief as you've decribed, I find it helpful to shift the focal point of my eyes slowly from the butt of the neck to the headstock and then back again. Then go down on your knees to bring your eyes level to just above the top nut. We start by discussing how and why the electronics components in your guitar effect the tone. This week we took in a 1960’s Fender P-Bass for a refret that had a severely warped neck. You'll see it when you look lengthwise down the neck. check out the FAQ by clicking the After the neck cools, the glue re-hardens and the neck holds it’s new, straighter, shape. Another way to check if your guitar is warped is to play the first string for example, and then play the 12th fret of the first string. Hey Steve! tone forum. You need to look really close to notice this. This page was generated at 10:06 PM. If I sight down the neck from body to head, I think,a slight dip/warp is noticeable on the bass string side of neck (as if the truss rod is causing a desired arch this side and not the other) Its hard to tell. Look down from the top of neck. Here’s the fretboard against a straight […] This allows the wood of the neck and the fingerboard to move in relation to one another as we bend the neck towards it’s proper orientation. I have an old Harmony Rocket with a neck that is so warped, you can’t play the upper parts of it without cancelling out the tones. The rod can be tightened or loosened. Or how to tell a fingerboard had shrinked due to dry fingerboard ? 1940 M1 Kay Bass. Eyeball the neck to check for warping. Talk with your fellow tone freaks on the web's liveliest (and friendliest!) To start viewing messages, This is a tell-tale sign that your guitar could possibly be warped. Actually, I hate the neck on the Rocket but the guitar had a good sound-when I was a teenager that is. Tech experts from Seymour Duncan are regularly on this forum, and are clearly labeled as employees of Seymour Duncan.