Thank you for your question. In order to provide most accurate advice I need the complete model number of the oven. How hard is the panel to replace? 3. But I am concerned that it might be something else since it only occurs during cleaning. On these particular models the keypad is built into the console so the entire assembly has to be replaced. Hi Gene! From what I’m hearing they are pretty expensive. If replacing the keypad membrane fails to remedy the problem then the EOC (Electronic Oven Control) will have to be replaced also. Very likely the EOC got damaged during that power surge. Iâ€™m glad to help you again. If any of the connections are loose or have a burned spots, it will cause a damage to the relay board. My smooth top stove is showing the F 10 code once in a while Frigidaire . What do I need to do ? Both of them should read no continuity. Sorry to hear you have more problems with your range. Worth your range repair or not? I really appreciate your help. Thank you, Both of them you can find in a local hardware store. PLEFMZ99ECC used to get f30 but now getting F7 12 and the front element wont turn off – any ideas ? I have a fridgidaire oven model number FGES3045KFF. Sad news but probably it’s time for a new range. 2. If any of them broke, fix it. Gene. You can find it on the frame behind the bottom drawer. Remove at least one wire from the heating element terminal and check the heating element for continuity. The correction is to order new EOC and replace the faulty one. No doubt about it and a new one would fix the problem. Unfortunately I don’t gave a m/n for my 5 year old Frigidaire gas stove, but I hope you can help me anyway. I have a Frigidaire gas stove. sensor??? present to your wife – a new range! // Jun 3, 2017 at 2:52 pm. If I set the oven to 350 for example, only the top broiler comes on, not the bottom. Per your description the temperature sensor checks OK. You can not check the EOC instrumentally. To replace it I took the cooktop loose from the stove and flipped it over. We shut off the juice and then waited 10 min. At this time the EOC has gone bad. Gene, Thank you for the advice. As soon as I can afford it I will be getting rid of all Frigidaire appliances. It could be two possible scenarios: The overlay is nothing else but piece of plastic with all keys marked on it. hello Gene My oven was overheating and had an F10 error code. Gene, If you are going to replace the EOC, you may want to order the overlay as well because it’s very easy to damage the old overlay during reinstallation. You may want to order the new overlay together with the EOC because it’s very easy to damage the old one during reinstallation. This week I replaced the sensor probe but immediately got the code and again horrible smell. // Nov 16, 2013 at 7:26 pm, I have the F10 error code ohm reading at the plug into the EOC is 35 m ohms the sensor its self read out right at a 1080 ohms so per your upper most diagnostic its pry the EOC but I also have separate relays. Or do you think there may be more to the problem? The part number for the latch motor assembly is 316464300. The EOC that we ordered was 316576600. Check the temperature sensor resistance as described previously. We have a Frigidaire CFEF372EC5 likely in need of EOC replacement. Please, verify and repost it. Unfortunately in today’s world it is possible the new EOC is defective. It will work fine sometimes and sometimes not. I have read about the F10.I have a Frigidaire free standing glass top stove. The part number for the relay board is 316442119. Looks like the EOC power supply which is integrated into the EOC has gone bad. There suppose to be one more letter at the end. Eric Johnson I have a PLES389ECE showing F30. Problem with frigidaire range oven model FGF366CS, letters “dr” appear on digital display and won’t allow me to operate oven. The wiring harness resistance indicates no connectivity (the purple wires coming from the EOC). Is there a way to calibrate it? thanks. Very likely the problem is a faulty relay board.